MikroElektronika mikromedia PIC24 User Manual

user's guide tomikrome iaboard for PIC24Compact development system rich with on-board peripherals for all-round multimedia development on PIC24FJ

Page 10Page 11The mikromedia for PIC24 development system comes with the PIC24FJ256GB110 microcontroller. This high-performance 16-bit micr

Page 10Page 11The microcontroller can be programmed in three ways:4. Programming the microcontroller010203Over USB HID mikroBootloaderUsing mikroProg

Page 12Page 13Programming with mikroBootloaderYou can program the microcontroller with bootloader which is preprogrammed into the device by d

Page 12Page 13step 3 – Select .hex le step 2 – Browsing for .hex le Figure 3-2: Browse for HEX Figure 3-3: Selecting HEX01Click on Browse for HEX bu

Page 14Page 15step 4 – .hex le uploadingFigure 3-4: Begin uploading Figure 3-5: Progress bar010101 01To start .hex le uploading click on Begin uploa

Page 14Page 15step 5 – Finish uploadFigure 3-6: Restarting MCUFigure 3-7: mikroBootloader ready for next job 0101To nish uploading click on OK button

Page 16Page 17The microcontroller can be programmed with mikroProg programmer and mikroProg Suite fo PIC software. The mikroProg programmer is connect

Page 16Page 17mikroProg Suite™ for PIC SoftwaremikroProg™ programmer requires special programming software called mikroProg Suite™ for PIC®.

Page 18Page 19Figure 5-1:Placing ICD2 connectorThe microcontroller can be also programmed with ICD2 or ICD3 programmer. These programmer is connected

Page 18Page 19Figure 5-3: ICD2 / ICD3 & mikroProg programmer connection schematicVCC-3.3PGC2PGD2VCC-3.3CN5M1X6MCLR# MCLR#MCLR#VCC-3.3RSTPGC2PGD2MC

Page 3I want to express my thanks to you for being interested in our products and for having condence in Mikroelektronika.The primary aim of our comp

Page 20Page 216. microSD Card SlotMOSI2-RG8SCK2-RG6MISO2-RG7VCC-3.3VCC-MMCVCC-MMCC38100nFVCC-MMCR1010KVCC-MMCR9 10KCN4MMC CARD MICROSD-CS# SD-CD# SD-C

Page 20Page 217. Flash Memory MOSI2-RG8MISO2-RG7SCK2-RG6FLASH-CS#VCC-3.3VCC-3.3FLASH-CS#FLASH-CS#MISO2-RG7SCK2-RG6MOSI2-RG8VCC-3.3R4810KC37100nFE910uF

The development system features a TFT 320x240 display covered with a resistive touch panel. Together they form a functional unit called a touch s

Page 23VCC-SYSVCC-SYSLCD-BLEDLED-KLCD-RSTPMD7TFT 320x240 displayPMD6PMD5PMD4PMD3PMD2PMD1PMD0PMRDPMWRLCD-RSLCD-CS#LCD-XRLCD-YDLCD-XLLCD-YU1234567891011

Page 24Page 25Figure 9-2: Inserting 3.5mm headphones jackThe mikromedia for PIC24 features MP3 codec audio controller VS1053. This module en

Page 24Page 25Figure 9-3: Audio module connection schematicVS1053MICPMICNXRESETDGND0CVDD0IOVDD0CVDD1DREQGPIO2GPIO3GPIO6GPIO7XDCSIOVDD1VCODGND1XTALOXTA

Page 26Page 27PIC24FJ256GB110 microcontroller has integrated USB OTG module, which enables you to implement USB communication functionality of your

Page 26Page 27Figure 10-2: USB module connection schematicMOSI2-RG8SCK2-RG6VCC-3.3USB-IDUSBDPUSBDMC2810nFR14100VCC-USBUSBDMUSB-DETUSB-IDUSBDPUSB-DETFP

Page 28Page 2911. AccelerometerOn board ADXL345 accelerometer is used to measure acceleration in three axis: x- y- and z-. The accelero

Page 28Page 29Board is equipped with 8Mhz crystal oscillator circuit that provides external clock to the microcontroller OSC pins. This base

Page 3Introduction to mikromedia for PIC24 4Package Contains 5Key Features 6System Specication 71. USB power supply 82. Battery power supply 93

Page 30Page 31RA0MOSI2-RG8MISO2-RG7SCK2-RG6MISO1-RC4STATFLASH-CS#RE8RE9RB5RB4RB3RB2RB1RB0VREF-1.8VSENSERB9RA1RF13RF14RF4RF5RF2RF8USBDMSCL2-RA2SCL1-RA1

Page 30Page 3114. PinoutSPI LinesInterrupt LinesAnalog LinesPrograming lines I2C LinesUART linesRemappable Comparator lines5V RST Reset pin5V power su

Page 32Page 3380.90 mm (3.18”)73.01 mm (2.87”)69.85 mm (2.75”)2.54 mm (0.10”)4.45 mm (0.17”) 2.77 mm (0.11”)60.56 mm (2.38”)5.08 mm (0.20”)36.55 mm (1

Page 32Page 33Notes:

Page 34Notes:

Page 34DISCLAIMERAll the products owned by MikroElektronika are protected by copyright law and international copyright treaty. Therefore, this manual

If you want to learn more about our products, please visit our website at www.mikroe.comIf you are experiencing some problems with any of our products

Page 5Page 4Introduction to mikromedia for PIC24The mikromedia for PIC24 is a compact development system with lots of on-board peripherals

Page 5Package Contains01 0204 050306Damage resistant protective boxmikromedia for PIC24development systemmikromedia for PIC24 user’s guidemikromedia

Page 6Page 7Key Features011602010203040506070809101112131415Connection PadsTFT 320x240 displayUSB MINI-B connectorLI-Polymer battery connector3.5mm he

Page 6Page 7System Specicationpower supplyOver a USB cable (5V DC)board dimensions8 x 6cm (3.14 x 2.36 inch)weight~50g (0.11 lbs)power consumption50m

Page 8Page 91. USB power supplyYou can provide power supply to the board using provided miniUSB connector. On-board voltage regulator will make sure t

Page 8Page 9You can also power the board using Li-Polymer battery, via on-board battery connector. On-board battery charger circuit MCP73832